Stiffener Sentence Examples | Use Stiffener in a sentence

1.powdery starch from certain sago palms; used in asia as a food thickener and textile Stiffener.

2.the trapezoidal Stiffener is taken as plate beam element, and its displacement model is built according to the deformation coordinate relationship between plate and Stiffener.

3.the rack uses the channel steel to take the main body, the middle with Stiffener board welded together.

4.next, apply a second coat to both the Stiffener and the disc, let them dry for a few minutes, and then press together.

5.this shows the small blocks glued to the Stiffener.

6.this indicated that the fracture had initiated at the unfused butt weld in the longitudinal Stiffener.

7.based on the model, the effects of the Stiffener width, Stiffener height and impact velocity of the projectile on the residual velocity were analyzed.

8.research on mechanical properties of box gird with longitudinal clapboard and stiffening rib the effect of Stiffener to the stability of i-steel beams

9.evolutionary structural optimization for Stiffener layout problem of plate structures

10.the Stiffener layout optimization of thin walled structures is addressed in this article using a topology optimization method.

11.research on design of critical external compressive resistance of buckling of Stiffener ring of underground penstock

12.the results showed that high cycle vibration has a greater impact on the side board, little influence on Stiffener; notch has little influence on the strength of the side board.

13.the failure mechanisms and the loading capacity of stiffened composite panels with Stiffener runout are studied.

14.the calculations analyzed various factors influencing the shear buckling of aluminum plates such as the width-to-thickness ratio, Stiffener spacing, alloy temper, and end post.

15.parameter analysis of connections with vertical Stiffener between the concrete-filled square tubular column and steel beam

16.according to the optimal parameters, the stamping of b-pillar Stiffener can be successfully processed to satisfy the quality requirement.

17.the design methods of the link including confirmation of its length and cross section, design of its rib Stiffener, design of its connection and lateral braces are emphasized.

18.the relatively small reduction in stress intensity magnification factor with increasing stiffness of the Stiffener.

19.using the programmable controller in the automobile rear axle house ring Stiffener, logic sequential control was realized in the top plate automatic welding craft.

20.the excess slightly beyond the Stiffener will be trimmed off later.

21.the shank is a Stiffener that controls the flexibility of the sole.

22.s bend box body thickness of each panel, Stiffener size and spacing of the Stiffener location, structural strength will be greatly affected.

23.the comparison of numerical results and experimental data shows that the cohesive element based model can simulate the propagation of delamination initiated at the Stiffener runout.

24.on the other hand, the definition of the background grid in the curvelined coordinate system makes it possible to perform Stiffener design of3d curved shells.

25.we have done some loading testing on the panel with different initial deflections and different Stiffener.

26.the cohesive element for the nonlinear finite element software abaqus is used to simulate the interface between the Stiffener and the skin.

27.the design parameters of chamber and Stiffener of hollow blade model were analyzed.

28.the proposed rebar Stiffener was found to be very effective in improving the static behavior of the composite connections.

29.some crack extension probably developed from the unfused section of the butt weld across the thickness of the Stiffener during transport and erection.

30.the relatively small reduction in stressintensity magnification factor with inereasing stiffness of the Stiffener.

31.design of Stiffener in the electronic cabinet based on the three-field coupling analysis

32.bulwark plate to be thickened and Stiffener to be added in way of mooring hole.

33.the codes and specifications of china in steel-structure field require that the bearing ability of shear force in panel zone must be sufficient and the inclined Stiffener should be applied.

34.the vertical Stiffener connection is suitable for rectangular steel tube column that the sectional area is smaller and h-steel beam connections.

35.effect of Stiffener of extended endplate connection on failure mode in fire

36.the kneading board and the inside lining Stiffener spreads across, the bearing power optimizes, leg each strengthens processing, the average distributed load;