Lath Sentence Examples | Use Lath in a sentence

1.they took their Lath swords, dumped their other traps on the ground, struck a fencing attitude, foot to foot, and began a grave, careful combat, "two up and two down."

2.the microstructures of heat affected zones of t91/ 10crmo910 are tempered sorbite and thin tempered Lath martensite and the toughness is good.

3.furthermore, both the effect of martensite Lath boundaries on the nucleation of dynamic recrystallization, and the mechanism of nucleation and growth of equiaxial nanometer grains were revealed.

4.the effect of microstructure on crack initiation and steady state propagation of Lath martensite

5.by the integration of numerical result and cnc programming, a new method which advances the efficiency at the cnc machining of arced Lath tool is provided.

6.this paper sets up the plastic energy consumption and tensile functions of the ideal rigid plastic steel wire and Lath under large curvature tension bending.

7.a as thin as a Lath women.

8.they are dislocated Lath martensite area and twinned martensite area respectively.

9.effect of Lath martensite morphology on the mechanical properties of steel

10.i must get a Lath even a small one for stuff like this.

11.Lath Lath should fitness of first selection appliance, be like dumbbell, barbell, pulling force implement, assorted fitness implement etc.

12.the dimension and dispersion of the precipitation decrease, the Lath character of bainitic ferrite tends to be evident.

13.the prodominant twin martensite and partial Lath martensite existed in dendrite.

14.the tempered Lath martensite grows up with the tempering temperature increasing, however the tendency of growing is not obvious.

15.the microstructure of surfacing metal is Lath martensite and carbide.

16.the microstructure of weld bead obtained by shielded metal arc welding are massive ferrite and a little pearlite, haz are Lath bainitic.

17.Lath length: up to 2440 mm or customized according to customer requirements.

18.the results indicated that there are some microtwins in Lath martensite.

19.fix the top Lath of the curtain onto the roller with the screws and washers provided.

20.a conventional plaster application using metal Lath mechanically fastened to the existing exterior and finished with a good acrylic cement finish is what is normally recommended.

21.there are many working procedure in a progressive die, and only one piercing Lath can finish the process from material to finished product.

22.the microstructures of the steel are fine Lath martensite after "zero time holding" quenched.

23.make-up: long edge of Lath made according to the actual needs of the90-degree angle to join together.

24.he's as thin as a Lath.

25.metal Lath and beads - definitions , requirements and test methods - part 1 : internal plastering.

26.metal Lath and beads - definitions , requirements and test methods - internal plastering.

27.this method is suggested because the weight of one full coating might be too much, and you would probably have some trouble keeping it in place on the Lath.

28.a series of morphologies of Lath microstructure can be attained by tmp.

29.the relationship between fracture toughness and notch toughness, tensile ductilities in Lath martensite steel has been investigated.

30.building works. gypsum plastered suspended metal Lath ceilings. technical specifications.

31.nb and re oxide could refine the microstructure, thus the hardness of hardfacing alloy could also be improved. the hardfacing alloys microstructure in this research were composed of Lath martensite, residual austenite and dotted carbides.

32.the microstructure evolution and grain-refining mechanism of the process, severe rolling of Lath martensite, was studied.

33.and when the quenching temperature is high, the chemical composition of the austenite grain can fully spread, while the defects in the crystal will be reduced, which would promote the formation of Lath martensite.

34.i don't have no stinking Lath!

35.metal Lath and beads - definitions , requirements and test methods - external rendering.