Kerf Sentence Examples | Use Kerf in a sentence

1.Kerf width increases in accordance with the changing of average power, peak power and pulse energy as pulse frequency is equal to pulse width.

2.the thesis evaluates the effect of all sorts of parameters on the Kerf surface quality and cutting depth.

3.the loss of the saw Kerf and recovery have be accurately calculated.

4.its saw Kerf is plat without burr and micro-cracks.

5.used seeds, Kerf seeds and middle cut seeds as explants, the result showed that middle cut seeds was the best explant, and the calli induction rate could reach to 72.97%. 2.

6.plausible trends and relationships between the Kerf characteristics and the process parameters are discussed together with the established empirical equations relating the input parameters to the Kerf geometry and quality for process control and optimization.

7.that slot left in the wood after a saw goes through is called the Kerf.

8.in the same of average power, peak power and duty cycle constant, pulse width is the primary parameter which affects the Kerf width.

9.it is performed through the verification and analysis of the interrelation of typical materials cutting features ( cutting depth, Kerf width, striking capacity) and cutting variables ( water pressure, target distance, cutting rate and so on) and the effects of abrasive and material.

10.application of the thin-Kerf sawblade in cutting of thin solid wood board

11.as a bonus, in researching this little factoid i discovered a new word i hadn't known before; Kerf.

12.application of Kerf and rock bolt in jinyuan gold co. , ltd.

13.comparing with oxygen, nitrogen produced brighter and smoother cut surface with smaller Kerf.

14.to reduce the Kerf width and to improve the Kerf quality, the experiments of ceramic cutting with water constricted plasma arc are carried out.

15.the effects on Kerf width and quality made by laser facula diameter, focal point position, cutting speed, laser power and other technological parameters were studied.

16.it was indicated that the seeds with the treatment of Kerf were the best, callus reduction rate could reach up to90.

17.study relation between spray nozzle flux and relative Kerf depth.

18.and some thin Kerf, but also are less likely to cut stone, cut so thin because of the stones will fracture stone.

19.optimize further for equipment, raise Kerf ability to lay a foundation.

20.features: low Kerf loss, high wood utilization rate, low noise, high durability;

21.besides, a formula of estimating the Kerf surface roughness was also presented, which can explain the experiment results well.

22.the results show that Kerf width decreases with pulse frequency increases under the same average power and pulse width.

23.the novel ring is characterized in that a Kerf is arranged on the original ring, and the primary snap ring and the secondary snap ring are arranged at two ends of the Kerf.

24.technical condition and experiment argumentation of antirust for the silicon steel sheet Kerf

25.the Kerf is the outside boundary of the tunnel wall that a boring machine gouges out as it bores through the ground or rock.

26.Kerf roughness and quality control of laser precision cutting

27.the effect of underwater consumable electrode arc cutting process parameters on Kerf shape was investigated, and the governing factors of underwater cutting arc stability was analyzed in this research.

28.the effects of laser process parameters on Kerf width and quality were studied.

29.the results show that the Kerf width increases with the increase of laser power, pulse frequency, pulse width and assist gas pressure, but decreases with the increase of cutting speed.

30.according to the evaluation criterion of velocity and mass flow rate, the gas dynamics performance of taper nozzle in Kerf excels obviously than that of convergence nozzle. and with the increasing of stand off distance, at least two reasonable cutting scopes exist.

31.particular attention is paid to the analysis of the effects of some major process parameters, such as air pressure, abrasive material, size and supply rate, nozzle shape and dimension, stand-off distance and workpiece material on the cutting performance and Kerf characteristics.

32.reject: the dicing Kerf is no square and unshaped

33.it can be seen from the results that the Kerf morphology and dimensions are influenced mostly by jet pressure, secondly by the nozzle feed rate and the standoff distance, and the abrasive flow has less effect on Kerf morphology and size.

34.in order to obtain high-quality Kerf, it is necessary to assure the accurate location of the focus.

35.frame out of 16 gauge hot-dip galvanized steel sheet with mineral wool infill & Kerf,

36.the effects of curvature radius and cutting speed on the top Kerf width of laser cutting of thin pipe with a small diameter

37.range of Kerf width and exposure may be changed for optimized performance.

38.based on the parameter model of laser cutting quartz crystal material, the relationship among laser power, cutting speed, material thickness and Kerf width is analyzed. and the basis regularities of laser cutting quartz crystal material are studied.

39.the basic principle and characteristics of the technology and the influencing factors to the machining process are introduced and discussed, together with the erosion mechanisms and Kerf characteristics.

40.this system is applied to the profile lining and cutting robot system, which improves the precision of lining and cutting and makes the Kerf smooth.